Who's Online Now
0 members (), 18 guests, and 30 robots.
Key: Admin, Global Mod, Mod
Newest Members
Thomas, Glen, pustekonto, Simon, Nbmod
403 Registered Users
Forum Statistics
Forums23
Topics353
Posts4,508
Members403
Most Online248
Mar 14th, 2020
Popular Topics(Views)
61,978 77-MGB
54,152 2020 Gardens
Top Posters
sonny 1,402
JIM 1,305
GatorS 249
Nnaatz 163
GLyford 110
Doc 68
chma 43
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Previous Thread
Next Thread
Print Thread
Rate Thread
#2464 04/19/2021 04:26 PM
Joined: Feb 2019
Posts: 163
Likes: 1
N
Nnaatz Offline OP
MBN member
OP Offline
MBN member
N
Joined: Feb 2019
Posts: 163
Likes: 1
Heres the 420 back in the shop last winter I had replaced the clutches and replaced all bearings and seals. Took it out pushed back the snow in the ditch then in spring I moved a pile off dirt to a low spot then sat rest of the summer and run as I needed. Went put it up for the winter; and grabbed the left clutch and no one was home...pressed plate had collapsed because of rust jacking.

Attached Images
Resizer_16188636013370.jpg (85.67 KB, 64 downloads)
Joined: Feb 2019
Posts: 163
Likes: 1
N
Nnaatz Offline OP
MBN member
OP Offline
MBN member
N
Joined: Feb 2019
Posts: 163
Likes: 1
Here is the clutch disassembled...couple steels and fibers were bonded....so sandblasting or evaporust on the steels and a light sanding to polish of the rust. Not to worried about talking to much...that are new and are thicker than the jd spec

Attached Images
Resizer_16188714745333.jpg (83.28 KB, 61 downloads)
Resizer_16188714745332.jpg (64.7 KB, 61 downloads)
Resizer_16188714745331.jpg (99.98 KB, 61 downloads)
Resizer_16188714745330.jpg (94.93 KB, 61 downloads)
Joined: Jan 2019
Posts: 1,402
Likes: 11
MBN veteran
Offline
MBN veteran
Joined: Jan 2019
Posts: 1,402
Likes: 11
Had a TD-9 that did that!---a real pain for sure!
After a good cleaning they should be good again,---well til the next time they stick!


"A machine you build yourself is a vote for a different way of life. There are things you have to earn with your hands."
Joined: Feb 2019
Posts: 163
Likes: 1
N
Nnaatz Offline OP
MBN member
OP Offline
MBN member
N
Joined: Feb 2019
Posts: 163
Likes: 1
Everything is pretty much new with only about 5 or 6 hrs of run time....derusting and back in it goes

Joined: Jan 2019
Posts: 1,402
Likes: 11
MBN veteran
Offline
MBN veteran
Joined: Jan 2019
Posts: 1,402
Likes: 11
At least they are not D-8 size! --- THAT would be a bear!


"A machine you build yourself is a vote for a different way of life. There are things you have to earn with your hands."
Joined: Jan 2019
Posts: 765
Likes: 58
B
MBN old hand
Offline
MBN old hand
B
Joined: Jan 2019
Posts: 765
Likes: 58
goin in deep so to speak,Nnaatz..get er done..an old Cat mechanic("Later Bob"-Ontario,-R.I.P.) told me once,"Fix 'er once,fix it right"

Joined: Feb 2019
Posts: 163
Likes: 1
N
Nnaatz Offline OP
MBN member
OP Offline
MBN member
N
Joined: Feb 2019
Posts: 163
Likes: 1
I ordered new and new pressure plate because it sat collapsed all winter

Joined: Jan 2019
Posts: 1,402
Likes: 11
MBN veteran
Offline
MBN veteran
Joined: Jan 2019
Posts: 1,402
Likes: 11
Sounds like the right way to go!


"A machine you build yourself is a vote for a different way of life. There are things you have to earn with your hands."
Joined: Feb 2019
Posts: 163
Likes: 1
N
Nnaatz Offline OP
MBN member
OP Offline
MBN member
N
Joined: Feb 2019
Posts: 163
Likes: 1
Steering clutches in...carb rebuilt....beer times

Attached Images
Resizer_16199053523020.jpg (113.3 KB, 35 downloads)
Joined: Jan 2019
Posts: 765
Likes: 58
B
MBN old hand
Offline
MBN old hand
B
Joined: Jan 2019
Posts: 765
Likes: 58
spend a little on it,then you know what you got..it'l serve you well..what shape are the track pads? can you regrouser them(add ribs)

Joined: Jan 2019
Posts: 1,402
Likes: 11
MBN veteran
Offline
MBN veteran
Joined: Jan 2019
Posts: 1,402
Likes: 11
IF you need rails, check out Pivot in INDY! ----- They had some right on the dock for my 310 case.


"A machine you build yourself is a vote for a different way of life. There are things you have to earn with your hands."
Joined: Feb 2019
Posts: 163
Likes: 1
N
Nnaatz Offline OP
MBN member
OP Offline
MBN member
N
Joined: Feb 2019
Posts: 163
Likes: 1
These pads had been caulked...they are what deere calls a double rib semi grouser. These provide me with all traction the 2 cylinder can suffer. Had flat street pads before I put these on...couldn't do much in winter

Attached Images
Resizer_16199759614110.jpg (154.23 KB, 26 downloads)
Joined: Jan 2019
Posts: 1,402
Likes: 11
MBN veteran
Offline
MBN veteran
Joined: Jan 2019
Posts: 1,402
Likes: 11
Thats what my 310 has ----- great for smaller tractors AND great for any crawler loader! ---- even MOOSE has the semi's on him!


"A machine you build yourself is a vote for a different way of life. There are things you have to earn with your hands."
Joined: Feb 2019
Posts: 163
Likes: 1
N
Nnaatz Offline OP
MBN member
OP Offline
MBN member
N
Joined: Feb 2019
Posts: 163
Likes: 1
Father in law has dozer grouser on his allis loader...we put clutches in it every other year

Joined: Jan 2019
Posts: 1,402
Likes: 11
MBN veteran
Offline
MBN veteran
Joined: Jan 2019
Posts: 1,402
Likes: 11
YA! On loaders you dont want too much traction! Just enough to hold you against the dig area,--- THEN let the hydraulics do the actual work. Track spin is needed a lot on units with direct drive! -- Power shift/fluid drive not so much as you can control the spin and traction while still loading the bucket with minimal spin. ---- Hard to x-plain, BUT you get the idea! lol!!


"A machine you build yourself is a vote for a different way of life. There are things you have to earn with your hands."

Link Copied to Clipboard
Recent Topics
What odd jobs did you do today?
by bunkclimber - 03/27/2024 11:56 AM
Member check in.
by sonny - 02/29/2024 12:10 PM
ShoutChat
Comment Guidelines: Do post respectful and insightful comments. Don't flame, hate, spam.
Today's Birthdays
There are no members with birthdays on this day.
Donation Box
Powered by UBB.threads™ PHP Forum Software 7.7.5